OK-6 Kick-Over Tool Assembly Gas Lift - Kick Over Tools OK-6 Kick-Over Tool Assembly OK-6 Kick-Over Tool Assembly The Rebco OK-6 Kickover Tool is a wireline service tool designed to install and retrieve compatible 1-in. OD side-pocket subsurface-control devices in appropriate Camco side-pocket mandrels. Used with a compatible running or pulling tool, the OK-6 uses a solid centralizer sleeve to guide and stabilize the tool assembly within the tubing while the locating and kickover components position the attached service tool at the selected side pocket. Product Code: 192 REQUEST A QUOTE DOWNLOAD DATASHEET OK-6 Kick-Over Tool Assembly OK-6 Kick-Over Tool Assembly Click here Applications Installing compatible 1-in. OD gas-lift valves and other side-pocket subsurface-control devices. Retrieving compatible 1-in. OD devices for replacement, inspection, or well servicing. Positioning an attached running or pulling tool at the selected side-pocket mandrel. Supporting wireline intervention in compatible mandrels equipped with the required orienting profile. Key Benefits Sleeve-type centralization: The solid centralizer sleeve provides an alternative method of guiding and stabilizing the tool in the tubing. Controlled pocket alignment: Locating and kickover components assist in orienting the attached service tool with the side pocket. Running and pulling capability: Supports both installation and retrieval when paired with the appropriate compatible service tool. Alternative tool configuration: Provides a centralizer arrangement different from the spring-based OK-5 design for applications where the sleeve configuration is specified. Notes Kick-over SPM Latch Running Tool Pulling Tool Pulling Spacer OK-1 KBMG KBUG BK-2 JK-2 1 ¼ in. JDS 1.66 in. SM - OK-6 OK-6 Centralizer Note: Verify that the tubing internal diameter and selected tool size are suitable for the sleeve-type centralizer configuration. Inspect the centralizer sleeve, locating finger, kick springs, and arm assembly before deployment in accordance with approved service procedures. Redress Kits Available: Rebco offers Major & Minor redress kits and replacement components for OK-6 Kickover Tools, including applicable sleeve-centralizer and kickover components. Provide the tool size and configuration to confirm the correct kit. TECHNICAL DATA NOMINAL SIZE 2 7/8” 3” 4 ½” ASSEMBLY NUMBER 192202462500 192202463000 192202464500 MAXIMUM OD 2.223” 2.500” 3.500” Tubing ID required for proper tool orientation 2.437” 2.921” 3.958” PIN THREAD CONNECTION 15/16” – 10 15/16” – 10 15/16” – 10 FISHING NECK OD 1.375” 1.375” 1.375” LENGTH 67.0” 71.125” 71.87” MATERIAL Alloy Alloy Alloy ACCESSORY: Service Tool: Type ‘ST’ for Detent Spring 5514151 RELATED TOOLS AO & AD Knuckle Joint Assembly VIEW Running Tools for Gas Lift VIEW JDS Pulling Tool (Medium Reach) Assembly VIEW OK-5 Kick-Over Tool Assembly VIEW Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

ROTRXN Running Tool Assembly Running Tools ROTRXN Running Tool Assembly ROTRXN Running Tool Assembly Rebco ROTRXN Running Tool is the same as ROTRX in its function; the difference is that ROTRXN utilizes Retainer Dogs instead of the Lugs to attach the Lock Mandrel. Rebco ROTRX Running Tool is designed to set Types: ROTR , ROTRN , ROTRQ , ROTRPT , ROTRNT , ROTX & ROTXN Locking Mandrels into its respective Nipple profiles. This Running Tool is generally used to install tubing safety valves in the uppermost Landing Nipples. This Running Tool is generally used to install tubing safety valves in the uppermost Landing Nipples. Product Code: 41 REQUEST A QUOTE DOWNLOAD DATASHEET ROTRXN Running Tool Assembly ROTRXN Running Tool Assembly Click here Applications All applications are identical to the ROTRX, where the lock mandrel attachment interface uses Retainer Dogs rather than Lugs. Setting ROTR, ROTRN, ROTRQ, ROTRPT, ROTRNT, ROTX, and ROTXN Lock Mandrels with retainer dog attachment Key Benefits The Retainer Dog interface provides a secure mechanical connection for mandrels designed for dog-style engagement. Functionally identical operation to the ROTRX, operators already familiar with ROTRX will require no additional training. Same broad size range and mandrel type compatibility as the ROTRX TECHNICAL DATA NOM SIZE LOCK MANDREL GUIDE ASSEMBLY PART NUMBER FISHING NECK TO ENGAGE ENGINEERING DATA TYPE SIZE ACTUAL OD FISHING NECK CONNECTION LENGTH PIN BOTTOM 3” ‘ROTX’ 2.750” 41131827511 2.31” 2.62” 2.313” 1 1/16” - 10 1 1/4” - 12 24.2” ‘ROTR’ 2.875” 41131828710 4” ‘ROTX’ 3.688” 41131836810 3.12” 3.62” 1 7/8” - 12 24.7” ‘ROTR’ ‘ROTX’ 3.813” 41131838110 2 1/8” - 12 ‘ROTR’ 41131838112 1 5/8” - 12 ‘ROTRQ’ 41131838111 2 1/8” - 12 ‘ROTR’ 4.000” 41131840010 1 7/8” - 12 ‘ROTR’ 4.125” 41131841210 2 1/8” - 12 ‘ROTRQ’ ‘ROTX’ 4.313” 41131843110 ‘ROTR’ 5” ‘ROTX’ 4.562” 41131845610 4.000” 4.50” 3.125” 2 1/2” - 10 24.8” ‘ROTRQ’ 41131845611 ‘ROTR’ 5.250” 41131852510 3” - 10 ‘ROTRNT’ 5.963” 41131859614 25.9” ‘ROTR’ 5.875” 411318105870 5.37” 3 3/8” - 12 29.31” 7” ‘ROTRQ’ 5.875” 41131858711 5.375” 5.81” 26.7” ‘ROTR’ 5.963” 41131859610 ‘ROTRQ’ ‘ROTRQ’ 6.000” 41131860010 3 3/8” - 10 RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

Anchor Type Stops Assemblies for Tubing Perforator Service Tools Anchor Type Stops Assemblies for Tubing Perforator Anchor Type Stops Assemblies for Tubing Perforator Rebco CS and/or TS Anchor Stops are designed to screw directly into the base of the Tubing Perforator, and as a unit, to be set at desired depth. Product Code: 62 CS Collar Stop Anchor Assemblies TS Slip Stop Anchor Assemblies REQUEST A QUOTE DOWNLOAD DATASHEET Anchor Type Stops Assemblies for Tubing Perforator Anchor Type Stops Assemblies for Tubing Perforator Click here Applications Providing a positive reactive anchor for the ROTAO Tubing Perforator during punch activation Eliminating the need for a separate anchor-setting wireline run before perforating CS: anchoring at collar recesses for the highest reliability in collar-coincident perforation depths TS: anchoring at any smooth-bore depth when collar locations do not align with the target perforation interval Multi-perforation programs where the perforator and anchor are retrieved, repositioned, and reset at each target depth Key Benefits Made up directly to the Tubing Perforator bottom connection, perforator and anchor run, set, and retrieve as a single unit Eliminates the need for a separate anchor-setting run, reducing the total number of wireline trips and rig time per perforation. CS provides the most reliable, collar-seated anchor available for perforating operations. TS provides depth flexibility for perforating at any tubing interval, independent of collar spacing. Both types are available in 2" – 4½" nominal sizes to match all standard Rebco ROTAO Perforator sizes. Spare parts recommendation: 3 each of Punch and Guide Bushing per job CS Collar Stop Anchor Assemblies Rebco CS Collar Stop Anchor is used in the Tubing as a Stop; screwed directly to the bottom of the Tubing Perforator, to be set and pulled as a unit. Special Collet OD for 3 1/2" Collar Stop Anchor that will pass through 2.750" Nipple is available. _ TS Slip Stop Anchor Assemblies Rebco TS Slip Stop Anchor is used in the Tubing as a Stop; screwed directly to the bottom of the Tubing Perforator, to be set and pulled as a unit. TECHNICAL DATA Type ‘CS’ Collar Stop Anchor Assemblies: NOMINAL SIZE 2” (2 3/8”) 2 1/2” (2 7/8”) 3 1/2” 4 1/2” ASSEMBLY NUMBER 6202142000 6202142500 6202143500 6202144500 ENGINEERING DATA: MAXIMUM OD 1.75” 2.19” 2.75” 3.75” PIN THREAD CONNECTION 5/16” - 10 1 1/16” - 10 1 1/16” - 10 1 1/16” - 10 FISHING NECK OD 1.375” 1.750” 2.313” 2.313” LENGTH 10.72” 11.31” 11.81” 11.61” MATERIAL Alloy Alloy Alloy Alloy Type ‘TS’ Slip Stop Anchor Assemblies: NOMINAL SIZE 2” (2 3/8”) 2 1/2” (2 7/8”) 3 1/2” 4 1/2” ASSEMBLY NUMBER 6215142000 6215142500 6215143500 6215144500 ENGINEERING DATA: MAXIMUM OD - SET IN PLACE 1.998” 2.492” 3.05” 3.75” PIN THREAD CONNECTION 15/16” - 10 1 1/16” - 10 1 1/16” - 10 1 1/16” - 10 FISHING NECK OD 1.375” 1.750” 2.313” 2.313” LENGTH - SET IN PLACE 14.25” 14.15” 16.05” 17.8” MATERIAL Alloy Alloy Alloy Alloy RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

Glossary HO Heavy Duty Rope Socket Assembly - Threaded Connection HO Heavy Duty Rope Socket Assembly - Threaded Connection The Rebco HO Heavy Duty Rope Socket is a high-load rope socket designed for demanding wireline applications. The wireline is passed through the body and into a purpose-built clamp sub-assembly, where socket screws mechanically trap and retain the wire with maximum holding force. The clamp design distributes load across the wire cross-section more evenly than a knot or disc wrap, making it the preferred choice for heavy fishing operations, aggressive jarring programs, or any application where conventional rope socket designs may be insufficient. Available in standard threaded connections, 1½"–2½" OD. Back to the Tool page PDF download HO Heavy Duty Rope Socket Assembly - Threaded Connection HO Heavy Duty Rope Socket Assembly - Threaded Connection Click here RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco ’s Terms and Conditions of Sale.

Glossary OTHER TYPES OF PLUG CHOKES OTHER TYPES OF PLUG CHOKES D. Circulating Type Chokes for Nipples (Product Code 20) Circulating Chokes restrict fluid flow in the tubing string and permit circulation from above, making them the tool of choice for flow measurement and production rate management. The restriction is created by a Bean (designated by a 64ths-of-an-inch orifice) seated in the choke body; a wide range of orifice sizes is available, allowing the operator to calibrate the flow rate to the well's specific requirements. Circulating Chokes are also commonly used to reduce production intentionally when full-rate flow is not desirable. Types available include ROTAX , ROTAR , ROTFWT , and ROTRZT . How to Order: Product Code 20. Specify nipple profile type, seal bore size, material, and Bean orifice size in 64ths of an inch. E. Circulating Blanking Plugs for Nipples (Product Code 20) Circulating Blanking Plugs hold pressure from below while allowing circulation from above, and can be held open to bypass fluid freely while running or pulling the plug. An internal valve is depressed during run-in and pull-out to allow fluid bypass, reducing hydraulic drag on the tool string. Types available include ROTCX , ROTCR , ROTFSB , ROTFWB , ROTRZB , ROTFGB , ROTFMB , and ROTRKB , covering the full range of BF , BR , and related nipple profiles in the Rebco completion system. How to Order: Product Code 20. Specify the nipple profile type, seal bore size, and required material. F. Pump-Through Plugs (Product Code 21) Pump-Through Plugs hold pressure from below while allowing fluid to be pumped downward through the plug assembly from above, without requiring the plug to be pulled. This allows the operator to displace fluids below the plug, stimulate a zone, or perform injection operations without first removing the plug with a wireline trip. Types available include RXO , RXN , XRO , and XRN , selected based on the nipple profile and seal bore size. How to Order: Product Code 21. Specify the nipple profile, seal bore size, and required material. G. Plug Chokes for Tubing (Product Code 20) Plug Chokes for Tubing are designed to withstand limited pressure differentials while allowing circulation from above in wells where no Landing Nipples are present, and set directly in the tubing bore. They are the tubing-set equivalent of the nipple-set circulating choke family, and the types available include ROTCW , ROTDW , ROTDD , and ROTCD , each suited to specific tubing sizes and pressure-holding requirements. How to Order: Product Code 20. Specify tubing size, type ( ROTCW , ROTDW , ROTDD , or ROTCD ), seal bore size, and material required. Back to the Tool page PDF download OTHER TYPES OF PLUG CHOKES OTHER TYPES OF PLUG CHOKES Click here RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco ’s Terms and Conditions of Sale.

ROTFMH Plug Choke with Removable Mandrel (Top No-Go) Plug Assemblies ROTFMH Plug Choke with Removable Mandrel (Top No-Go) ROTFMH Plug Choke with Removable Mandrel (Top No-Go) Rebco ROTFMH Plug Choke with Removable Mandrel is a positive blank-off device designed to seal off pressure from above and below. The Plug Assembly is a Top No-Go device to be set in BF Landing Nipple and upper seal bore of the ROTL Sliding Sleeve. The Plug requires TWO runs to be set. Product code: 21 REQUEST A QUOTE DOWNLOAD DATASHEET ROTFMH Plug Choke with Removable Mandrel (Top No-Go) ROTFMH Plug Choke with Removable Mandrel (Top No-Go) Click here Applications Large-bore positive blank-off and bidirectional pressure sealing in BF Landing Nipples and the upper seal bore of the ROTL Sliding Sleeve, for seal bore sizes of 2.750" through 3.813." Top No-Go depth reference at the nipple for confirmed plug positioning at larger bore sizes Two-run setting with the ROTGS Running and Pulling Tool and ROTM Prong Key Benefits Extends the removable mandrel and Top No-Go plug capability into the large-bore range of 2.750" to 3.813" seal bore, filling the gap above the ROTFWG family's coverage. Uses the ROTGS and ROTM tool system, which is consistent with other large-bore lock mandrel tools in Section XIV, keeping the tool inventory integrated. Norm Alloy construction for H2S service. Available in a variety of materials to suit downhole conditions. Plug Chokes are available in a variety of Materials, suitable for down-hole conditions. Norm Alloy is suitable for H 2 S Service (NACE MR-01-2 75, Latest Revision) TECHNICAL DATA NIPPLE SEAL BORE SIZE 2.750” 2.813” 3.688” 3.750” 3.813” ASSEMBLY NUMBER 2125090627530 2125090628130 2125090636830 2125090637530 2125090638130 ENGINEERING DATA MAXIMUM OD (NO-GO) 2.803” 2.872” 3.740” 3.802” 3.864” FISHING NECK SIZE LOCK MANDREL 2.31” 2.31” 3.12” 3.12” 3.12” EQUALIZING PRONG 2.313” 2.313” 3.125” 3.125” 3.125” LENGTH 36.41” 36.41” 44.63” 44.63” 44.63” MATERIAL * Norm Alloy Norm Alloy Norm Alloy Norm Alloy Norm Alloy TOOLS REQUIRED: RUNNING/PULLING TOOL - ROTGS 40051427500 40051427500 40051436804 40051436804 40051436804 RUNNING/PULLING PRONG - ROTM 41092750 41092810 41094500 41094500 41094500 EQ. PRONG RUNNING/PULLING TOOL - SB 4014013000 4014013000 4014014000 4014014000 4014014000 * Norm Alloy is suitable for H2S Service (NACE MR-01-75, Latest Revision) RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

Glossary JDC Pulling Tool (Short Reach) Assembly JDC Pulling Tool (Short Reach) Assembly The Rebco JDC is a shear-down, short-reach pulling tool designed to retrieve sub-surface devices with external fishing necks in applications where the fishing neck is positioned close to the top of the device, meaning a shorter reach is both sufficient and preferred. The JDC engages the external fishing neck by allowing its dogs to snap over and behind the fishing neck shoulder as the tool is lowered over the device. Once latched, upward tension on the wireline lifts the device from its set position. If the device is stuck and cannot be freed, a firm downward jar stroke shears the internal shear pin, collapsing the dogs inward and releasing the JDC from the fishing neck, allowing the tool string to be retrieved without the device. The short-reach configuration of the JDC means the distance between the bottom of the core and the dog-engaging surface is intentionally minimized, making the JDC the correct choice when the gap between the top of the landing nipple and the fishing neck is small, or when working in completions with closely spaced nipples where a long-reach tool risks engaging the wrong fishing neck. Changing the core is all that is required to obtain a different reach within the same nominal size; no full tool replacement is necessary. Available in nominal sizes 1¼" through 4", engaging fishing neck ODs from 0.875" to 3.125". Alloy construction throughout. How to Order: Available in assembly numbers from 400703021250 (1¼") to 400703024000 (4"). Specify the nominal size and confirm the reach against the device's fishing neck dimensions for the retrieved device. Pinning Tool Assembly and Core Wrench are ordered separately by nominal size Back to the Tool page PDF download JDC Pulling Tool (Short Reach) Assembly JDC Pulling Tool (Short Reach) Assembly Click here RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco ’s Terms and Conditions of Sale.

Glossary ROTJ Running Tool Assembly ROTJ Running Tool Assembly The Rebco ROTJ Running Tool is a direct-shear-pin engagement running tool designed specifically for setting sub-surface devices with external fishing necks. The ROTJ connects to the device by threading a shear pin through the running tool body and into the fishing neck of the sub-surface device, holding the two together as a single unit during the trip downhole. Once the device reaches its target depth and is properly seated within the landing nipple, an upward jar stroke shears the retaining pin, freeing the running tool from the device and allowing the tool string to be retrieved to the surface. The ROTJ is a straightforward, reliable tool valued for its simplicity. There are no collet fingers, no latching dogs, and no hydraulic components to service. The running neck ID, which determines the size of the fishing neck the ROTJ will engage, varies by the type of sub-surface tool being installed. Operators should specify the fishing neck size or tool type when ordering to ensure proper fit. Available in nominal sizes ¾" through 4", with lengths ranging from 2.44" to 5.62". All sizes feature alloy construction with matched-pitch pin threads and fishing-neck connections. How to Order: Specify the nominal size and fishing neck size, or the tool type, when ordering, as the running neck ID varies by sub-surface device. Assembly numbers range from 410736 (¾") to 410725 (4"). Contact Rebco if the standard ROTJ is not suitable for the specific fishing neck configuration. Back to the Tool page PDF download ROTJ Running Tool Assembly ROTJ Running Tool Assembly Click here RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco ’s Terms and Conditions of Sale.

Glossary BD Lead Filled Stem (Weight Bar) BD Lead Filled Stem (Weight Bar) The Rebco BD Lead-Filled Stem is the RQLD quick-lock version of the Rebco BO , combining the same high-density lead fill with Rebco's double-shoulder Quick Lock System for faster field assembly. All operational cautions regarding use in jarring applications apply equally to the Type BD . Available in RQLD connections, 1½"–2½" OD. Important: Must not be used in jarring applications Note: RQLD stands for ( Rebco Quick Lock Disconnect) Back to the Tool page PDF download BD Lead Filled Stem (Weight Bar) BD Lead Filled Stem (Weight Bar) Click here RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco ’s Terms and Conditions of Sale.

ROTR & ROTX Selective Test Tool Assembly Test Tools and Check Valves ROTR & ROTX Selective Test Tool Assembly ROTR & ROTX Selective Test Tool Assembly Rebco ROTR & ROTX Selective Test Tool is designed to locate and set in compatible Landing Nipples in the tubing string and hold applied pressure from above. ROTR & ROTX Selective Test Tools are used to test tubing, locate leaks and other practical functions. Product Code: 14 REQUEST A QUOTE DOWNLOAD DATASHEET ROTR & ROTX Selective Test Tool Assembly ROTR & ROTX Selective Test Tool Assembly Click here Applications Multi-zone tubing pressure testing in completions with multiple ROTR/ROTRN Landing Nipples, testing each zone in a single wireline run Targeted leak location in a specific tubing zone without having to test from the bottom up Setting high-pressure hydraulic packers requiring seal integrity above and below the set depth Any application where selective placement among multiple same-size nipples is operationally required Key Benefits The selective locking mechanism allows precise nipple targeting in multi-nipple completions, with no risk of inadvertently setting in the wrong nipple. Multi-nipple repositioning in a single run eliminates additional wireline trips, a major time- and cost-saving in multi-zone testing programs. Among the highest pressure ratings in the Rebco test tool range, up to 18,500 psi against ROTR nipples SSJ Pulling Tool provides both running and retrieving capability, a single tool for the complete operation Compatible with both ROTR and ROTRN nipple profiles in the same assembly The Keys (retracted); the tool is run to a point below the desired compatible nipple, pulling up through the nipple releases the locking keys to set the tool. Pressure from above may then be applied. The process can be repeated with next nipple up the tubing string, thus eliminating number of Wireline trips. Rebco ROTX Selective Test Tool selectively locates and lands in ROTX Landing Nipples and/or Type ROTX Sliding Sleeve of the same size within a tubing string. The No-Go shoulder, also allows the Tool to be set into the ROTXN , No-Go Landing Nipple. The Test Tool is designed to hold pressure differential from above only. Installed or retrieved by standard Wireline procedure, the Tool can be set in the Landing Nipple, or repeatedly moved to the next higher Nipple of the same size. The pressure is equalized across the Test Tool by picking up the Drop with a Pulling Tool attached to the Fishing Neck. TECHNICAL DATA NOMINAL SIZE 2 7/8” 3 1/2” LANDING NIPPLE PROFILE ROTR ROTRN ROTR ROTRN SEAL SIZE 2.313” 2.562” ASSEMBLY NUMBER 14182023100 14132025600 ENGINEERING DATA: OD - with KEYS EXPANDED 2.62” 2.89” OD - NO-GO 2.307” 2.557” PACKING OD 2.313” 2.562” FISHING NECK OD 1.375” 1.375” BOTTOM THREAD 1” LP 1” LP LENGTH 24.75” 26.0” MATERIAL Alloy Alloy PRESSURE RATING from ABOVE ROTR Nipple 18,500 psi 19,000 psi ROTRN Nipple 17,000 psi 18,000 psi RUNNING/PULLING TOOL SSJ (PRODUCT 40) 401414072000 401414072000 NOMINAL SIZE 2” 2 7/8” 3 1/2” 3 1/2” LANDING NIPPLE PROFILE ROTX ROTXN ROTX ROTXN ROTX ROTXN ROTX ROTXN SEAL SIZE 1.875” 2.313” 2.750” 2.813” ASSEMBLY NUMBER 14182018700 14182023100 14182027500 14182028100 ENGINEERING DATA: OD - with KEYS EXPANDED 2.20” 2.62” 3.10” 3.16” OD - NO-GO 1.870” 2.307” 2.745” 2.803” PACKING OD - MAX. 1.875” 2.313” 2.750” 2.813” FISHING NECK OD 1.375” 1.375” 1.750” 1.750” BOTTOM THREAD 23.08” 24.50” 26.12” 26.12” LENGTH 3/8” NPT 1” LP 1” LP 1” LP MATERIAL Alloy Alloy Alloy Alloy PRESSURE RATING from ABOVE (Set in Nipple) ROTX 10,000 psi 10,000 psi 9,000 psi 9,000 psi ROTXN 8,000 psi 8,000 psi 8,000 psi 8,000 psi RUNNING/PULLING TOOL SSJ (PRODUCT 40) 401414072000 401414072000 401414072500 401414072500 RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.