Glossary SP Sand Pump (Bailer) Assembly SP Sand Pump (Bailer) Assembly The Rebco SP Sand Pump Bailer is a pump-action debris recovery tool that removes accumulated sand, scale, loose solids, and wellbore debris from the tubing or casing bore using a conventional reciprocating piston lift-pump mechanism. The tool consists of a top sub with a fishing neck, a piston assembly within the main barrel, and an interchangeable bottom valve shoe, available in ball, flapper, or junk-catcher configurations to suit different debris types and wellbore conditions. As the tool string is alternately lowered and raised at the surface, the piston moves up and down within the barrel: on the downstroke, the bottom valve opens, and debris-laden fluid enters the barrel below the piston; on the upstroke, the bottom valve closes, and the piston lifts the captured material upward within the barrel, loading the tool for retrieval. For large-volume debris accumulations where a single barrel capacity is insufficient, the Sand Pump Bailer can be converted to a tandem configuration by connecting a double-pin sub and an additional barrel below the primary unit, effectively doubling the recovery volume without requiring an additional wireline run. The operator should move the tool slowly downward onto the debris accumulation and then raise it sharply and repeatedly to maximize pump efficiency. At least 15 pump strokes are recommended before retrieving the tool to assess recovery. If debris has hardened or compacted to a point where pump action alone is insufficient, chemical solvents or mechanical loosening by light jar-down action prior to bailer deployment can improve results. Available with ball-type, flapper-type, or junk-catcher-type bottom shoe configurations, all of which are also available with optional mule shoe bottoms for guided approach. Standard barrel length is 5 ft. Available in 1½"–3" OD. Back to the Tool page PDF download SP Sand Pump (Bailer) Assembly SP Sand Pump (Bailer) Assembly Click here RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco ’s Terms and Conditions of Sale.

Valve ROTXX Plug Choke Assembly Plug Assemblies Valve ROTXX Plug Choke Assembly Valve ROTXX Plug Choke Assembly Rebco ROTXX Plug Choke Assembly, when landed in Type ROTX Landing Nipple , of the same size, will plug off the nipple and tubing. The Plug Choke is capable of holding pressure differentials from above or below. NOTE: Valve ROTXX Plug Choke Assembly is made up of ROTX Lock Mandrel (PRODUCT CODE 10, 17, and/or 18) and ROTX Equalizing Valve Sub-Assembly with a Cap (PRODUCT CODE 20) . Product Code: 20 REQUEST A QUOTE DOWNLOAD DATASHEET Valve ROTXX Plug Choke Assembly Valve ROTXX Plug Choke Assembly Click here Applications Plugging and pressure isolation from both above and below in ROTX Landing Nipples, across seal bore sizes of 1.500" through 4.562." Small-bore completions beginning at 1.500" seal bore, where the ROTX nipple profile is the completion standard Single-run plug setting for efficient wireline operations H2S service environments requiring Norm Alloy construction Key Benefits The smallest available seal bore coverage in the valve-type plug choke family, starting at 1.500", addresses velocity strings and small-diameter production tubing not served by the ROTRR series. Single-run setting reduces the number of wireline trips required. ROTX-specific Running and Pulling Tools, Equalizing Prongs, and Check Set Tools are fully specified per size in the engineering data tables. Bidirectional pressure holding provides complete tubing isolation. Available in a variety of materials to suit downhole conditions. The Plug requires ONE run to be set. Norm Alloy is suitable for H 2 S Service (NACE MR-01-2 75, Latest Revision) Plug Chokes are available in a variety of Materials, suitable for down-hole conditions. TECHNICAL DATA NIPPLE SEAL BORE SIZE 1.500” 1.625” 1.875” 2.313” ASSEMBLY NUMBER 20181815030 20181816230 20181818730 20181823130 ENGINEERING DATA MAXIMUM OD (NO-GO) 1.495” 1.620” 1.870” 2.307” LOCK MANDREL FISHING NECK ID 1.06” 1.06” 1.38” 1.81” RUNNING TOOL - ROTX 41182015000 41182016200 41182018700 41182023100 PULLING TOOL - ROTGR 40051315000 40051315000 40051318700 40051323100 EQUALIZING PRONGS RUNNING 49121324 4912496 4912505 4911793 PULLING 49122037 49122035 49122044 49122078 LENGTH 22.75” 22.75” 20.28” 20.75” MATERIAL * Norm Alloy Norm Alloy Norm Alloy Norm Alloy ACCESSORY (PRODUCT CODE 41) : CHECK SET TOOL 4102181500 4102181500 4102181870 4102182310 NIPPLE SEAL BORE SIZE 2.750” 2.813” 2.875” 3.313” ASSEMBLY NUMBER 20181827530 20181828130 20181828730 20181833130 ENGINEERING DATA MAXIMUM OD (NO-GO) 2.745” 2.808” 2.870” 3.307” LOCK MANDREL FISHING NECK ID 2.31” 2.31” 2.31” 2.62” RUNNING TOOL - ROTX 41182027500 41182028100 41182028700 41182033100 PULLING TOOL - ROTGR 40051327500 40051327500 40051327500 40051331202 EQUALIZING PRONGS RUNNING 4912599 4912599 4912599 4911762 PULLING 49122043 49122043 49122043 4911763 LENGTH 20.77” 20.77” 20.77” 23.8” MATERIAL * Norm Alloy Norm Alloy Norm Alloy Norm Alloy ACCESSORY ( (PRODUCT CODE 41) : CHECK SET TOOL 4102183000 4102183000 4102183000 4102183310 NIPPLE SEAL BORE SIZE 3.688” 3.813” 4.313” 4.562” ASSEMBLY NUMBER 20181836830 20181838130 20181843130 20181845630 ENGINEERING DATA MAXIMUM OD (NO-GO) 3.682” 3.807” 4.307” 4.556” LOCK MANDREL FISHING NECK ID 3.12” 3.12” 3.12” 4.00” RUNNING TOOL - ROTX 41182036800 41182038100 41182043100 41182045600 PULLING TOOL - ROTGR 40051336804 40051336804 40051336804 40051345600 EQUALIZING PRONGS RUNNING 4911826 4911640 4911640 4911805 PULLING 4911827 4911641 4911641 4911944 LENGTH 21.88” 21.88” 22.0” 23.99” MATERIAL * Norm Alloy Norm Alloy Norm Alloy Norm Alloy ACCESSORY ( (PRODUCT CODE 41) : CHECK SET TOOL 4102183680 4102183810 4102184310 4102184560 * Norm Alloy is suitable for H2S Service (NACE MR-01-75, Latest Revision) RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

A Stem (Weight Bar) Tool String A Stem (Weight Bar) A Stem (Weight Bar) Rebco A Solid Bar Stems are with Threaded Connections - (1 1/4" - 2 1/2" Sucker Rod Type) 3/8" and 1/2" Diameter Stem is used for Velocity String Type completions. Note: All Rebco Tools have machined Flats for safer use. Product Code: 101 REQUEST A QUOTE DOWNLOAD DATASHEET A Stem (Weight Bar) A Stem (Weight Bar) Click here Applications Primary downhole weight source to overcome wellhead pressure, stuffing box friction, and fluid drag Generating impact force for upward and downward jarring operations Placed immediately above the jars to maximize impact at the downhole tool Key Benefits Solid alloy steel construction provides reliable, consistent weight per foot. Available in 2 ft, 3 ft, and 5 ft lengths for precise weight adjustment in the field Machined flats for safe wrench handling; never requires gripping on the fishing neck. Wide OD range from ⅜" to 2½" covers all standard tubing sizes. Special, well-conditioned material options are available. Alloy material is used to manufacture Rebco Stems; for severe conditions more suitable materials are available. TECHNICAL DATA ASSEMBLY PART NUMBER NOMINAL SIZE (OD) ENGINEERING DATA LENGTH THREAD CONNECTIONS FISHING NECK 101000372 3/8” 24” 1/4” - 20 UNC None 101000373 36” 101000375 60” 101000502 1/2” 24” 3/8” - 16 UNC None 101000503 36” 101000505 60” 101000752 3/4” 24” 1/2” - 13 UNC .687” 101000753 36” 101000755 60” 101001002 1” 24” 5/8” - 11 UNC .750” 101001003 36” 101001005 60” 101001252 1 1/4” 24” 15/16” - 10 UNS 1.187” 101001253 36” 101001255 60” 101001502 1 1/2” 24” 1.375” 101001503 36” 101001505 60” 101001752 1 3/4” 24” 1 1/16” - 10 UNS 1.750” 101001753 36” 101001755 60” 101001872 1 7/8” 24” 101001873 36” 101001875 60” 101002122 2 1/8” 24” 101002123 36” 101002125 60” 101002502 2 1/2” 24” 2.313” 101002503 36” 101002505 60” 101002512 24” 1 9/16” - 10 UNS 101002513 36” 101002515 60” RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

Valve ROTRRN Plug Choke Assembly Plug Assemblies Valve ROTRRN Plug Choke Assembly Valve ROTRRN Plug Choke Assembly Rebco ROTRRN Plug Choke Assembly, when landed in ROTRN Landing Nipple , of the same size, will plug off the nipple and tubing. The Plug Choke is capable of holding pressure differentials from above or below. NOTE: Valve ROTRR Plug Choke Assembly is made up of ROTRN Lock Mandrel (PRODUCT CODE 10, 17, and/or 18) and ROTR Equalizing Valve Sub-Assembly with a Cap (PRODUCT CODE 20) . Product Code: 20 REQUEST A QUOTE DOWNLOAD DATASHEET Valve ROTRRN Plug Choke Assembly Valve ROTRRN Plug Choke Assembly Click here Applications Plugging and pressure isolation from both above and below in ROTRN Landing Nipples, across seal bore sizes of 1.710" through 4.813." Single-run plug setting with a positive No-Go depth stop, providing an additional level of positioning certainty compared to the selective ROTRR Well shut-in, zone isolation, and pressure holding applications where the No-Go landing profile is already present in the completion string H2S service environments requiring Norm Alloy construction Key Benefits The No-Go bottom shoulder provides a positive mechanical depth stop at the nipple, adding certainty to depth positioning that a selective plug cannot. The single-run setting, identical to the ROTRR, maintains high operational efficiency. Shares all Running Tools, Pulling Tools, and Equalizing Prong numbers with the ROTRR series for the same seal bore sizes, minimizing tool inventory requirements. Check Set Tool (Product Code 41) is available for all sizes. Available in a variety of materials to suit downhole conditions. The Plug requires ONE run to be set. Plug Chokes are available in a variety of Materials, suitable for down-hole conditions. Norm Alloy is suitable for H 2 S Service (NACE MR-01-2 75, Latest Revision) TECHNICAL DATA NIPPLE SEAL BORE SIZE 1.710” 1.781” 1.875” 2.000” ASSEMBLY NUMBER 2013131017130 2013131017830 2013131018730 2013131020030 ENGINEERING DATA MAXIMUM OD (NO-GO) 1.705” 1.776” 1.870” 1.995” LOCK MANDREL FISHING NECK ID 1.06” 1.38” 1.38” 1.38” RUNNING TOOL - ROTR 41132017100 41132017800 41132018700 41132020000 PULLING TOOL - ROTGR 40051315000 40051317800 40051318700 40051318700 EQUALIZING PRONGS RUNNING 49121324 4911793 4911793 4911793 PULLING 49122037 49122078 49122078 49122078 LENGTH 20.5” 20.5” 20.5” 20.5” MATERIAL * Norm Alloy Norm Alloy Norm Alloy Norm Alloy ACCESSORY (PRODUCT CODE 41) : CHECK SET TOOL 4102131710 4102132000 4102132000 4102132000 NIPPLE SEAL BORE SIZE 2.125” 2.188” 2.313” 2.562” ASSEMBLY NUMBER 2013131021230 2013131021830 2013131023130 2013131025630 ENGINEERING DATA MAXIMUM OD (NO-GO) 2.120” 2.183” 2.308” 2.557” LOCK MANDREL FISHING NECK ID 1.38” 1.81” 1.81” 1.81” RUNNING TOOL - ROTR 41132021200 41132021800 41132023100 41132025600 PULLING TOOL - ROTGR 40051318700 40051321800 40051323100 40051323100 EQUALIZING PRONGS RUNNING 4911793 49121325 49121325 4912505 PULLING 49122078 49122081 49122081 49122044 LENGTH 20.5” 20.9” 20.9” 20.4” MATERIAL * Norm Alloy Norm Alloy Norm Alloy Norm Alloy ACCESSORY ( PRODUCT CODE 41) : CHECK SET TOOL 4102132000 4102132180 4102132310 4102132560 NIPPLE SEAL BORE SIZE 2.750” 2.813” 3.437” 3.688” ASSEMBLY NUMBER 2013131027530 2013131028130 2013131034330 2013131036830 ENGINEERING DATA MAXIMUM OD (NO-GO) 2.745” 2.808” 3.432” 3.683” LOCK MANDREL FISHING NECK ID 2.31” 2.31” 2.62” 3.12” RUNNING TOOL - ROTR 41132027500 41132028100 41132034300 41132036800 PULLING TOOL - ROTGR 40051327500 40051327500 40051331202 40051336804 EQUALIZING PRONGS RUNNING 49121119 49121119 4911882 4911826 PULLING 49122085 49122085 4911881 4911827 LENGTH 20.77” 20.77” 21.62” 21.88” MATERIAL * Norm Alloy Norm Alloy Norm Alloy Norm Alloy ACCESSORY ( PRODUCT CODE 41) : CHECK SET TOOL 4102133000 4102133000 4102133430 4102133680 NIPPLE SEAL BORE SIZE 3.813” 4.125” 4.313” 4.813” ASSEMBLY NUMBER 2013131038130 2013131041230 2013131043130 2013131048130 ENGINEERING DATA MAXIMUM OD (NO-GO) 3.808” 4.120” 4.308” 4.808” LOCK MANDREL FISHING NECK ID 3.12” 3.12” 3.12” 4.00” RUNNING TOOL - ROTR 41132038100 41132041200 41132043100 41132048100 PULLING TOOL - ROTGR 40051336804 40051336804 40051336804 40051345600 EQUALIZING PRONGS RUNNING 4911762 49111012 4911640 4911943 PULLING 4911763 49111148 4911641 4911944 LENGTH 22.3” 21.9” 21.9” 23.9” MATERIAL * Norm Alloy Norm Alloy Norm Alloy Norm Alloy ACCESSORY ( PRODUCT CODE 41) : CHECK SET TOOL 4102133810 4102134120 4102134310 4102134810 * Norm Alloy is suitable for H2S Service (NACE MR-01-75, Latest Revision) RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

ROTZ-1 & ROTZ-2 Lock Mandrel Sub-Assembly Lock Mandrels ROTZ-1 & ROTZ-2 Lock Mandrel Sub-Assembly ROTZ-1 & ROTZ-2 Lock Mandrel Sub-Assembly Rebco ROTZ-1 & ROTZ-2 is a Bottom No-Go, Non Flowing Lock. Lock Mandrel Sub-Assembly has Locks (Dogs) facing up which prevent upward movement, but depends on accessory No-Go shoulder to prevent the Lock Mandrel from downward movement. The Lock Mandrel can be used in a Bottom No-Go type Nipple only. Product Code: 10 REQUEST A QUOTE DOWNLOAD DATASHEET ROTZ-1 & ROTZ-2 Lock Mandrel Sub-Assembly ROTZ-1 & ROTZ-2 Lock Mandrel Sub-Assembly Click here Applications Bottom No-Go, non-flowing lock applications where depth control is referenced from below by the accessory's No-Go shoulder Completions using Bottom No-Go type nipples only; the ROTZ cannot be used in a Top No-Go nipple Nominal tubing sizes from 1.660" through 4.50", with seal bore coverage from 1.18" to 3.81" Key Benefits The Bottom No-Go design complements the ROTW Top No-Go offering, giving operators a choice of No-Go orientation to suit the nipple type already installed in the completion string. Upward-facing Dogs provide secure resistance against upward displacement once the lock is set. The No-Go function is built into the accessory rather than the lock body, allowing the same sub-assembly to be paired with different accessories while maintaining correct depth positioning. Available in a variety of materials for downhole service conditions. NOTE: Required Running and Pulling Tools with appropriate Probes are shown in ENGINEERING DATA for Type of Accessories attached to the Lock Mandrel Sub-Assembly. Rebco ROTZ-1 & ROTZ-2 Lock Mandrel Sub-Assemblies are available in variety of Materials, suitable for down-hole conditions. TECHNICAL DATA NOMINAL SIZE 1.660” 1.900” 2 1/16” 2 3/8” SEAL BORE SIZE 1.18” - 1.25” 1.43” - 1.50” 1.56” 1.78” - 1.87” SUB ASSEMBLY TYPE of LOCK ‘ROTZ-1’ ‘ROTZ-2’ ‘ROTZ-2’ ‘ROTZ-2’ SUB-ASS’Y NUMBER 10221201660 10222201900 10222202060 10222202370 ENGINEERING DATA MAXIMUM OD 1.156” 1.406” 1.531” 1.750” FISHING NECK SIZE .875” 1.187” 1.187” 1.375” MINIMUM ID .87” .75” .75” .88” LENGTH 6.12” 6.62” 6.44” 7.53” MATERIAL Alloy Alloy Alloy Alloy NOMINAL SIZE 2 7/8” 3 1/2” 3 1/2” 4 1/2” SEAL BORE SIZE 2.25” - 2.31” 2.56” 2.75” - 2.81” 3.68” - 3.81” SUB ASSEMBLY TYPE of LOCK ‘ROTZ-2’ ‘ROTZ-2’ ‘ROTZ-2’ ‘ROTZ-1’ SUB-ASS’Y NUMBER 10222202870 10222202560 10222203500 10221204500 ENGINEERING DATA MAXIMUM OD 2.188” 2.500” 2.688” 3.562” FISHING NECK SIZE 1.750” 1.750” 2.313” 3.125” MINIMUM ID 1.19” 1.20” 1.44” 2.06” LENGTH 7.69” 8.25” 10.47” 9.93” MATERIAL Alloy Alloy Alloy Alloy RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

Glossary RMF Pulling Tool Assembly RMF Pulling Tool Assembly The Rebco RMF is a unique dual-mode pulling tool capable of releasing via upward or downward jarring, making it the most operationally flexible pulling tool in the Rebco catalogue for external fishing neck retrieval. The RMF is selected for situations where the operator is uncertain which release direction will be effective, or where well conditions may make one direction unreliable, and wants the option to attempt release in either direction without pulling out of the hole to change tools. The dual-release capability also provides a practical safety benefit: if an upward jar attempt to release from a stuck device is unsuccessful (for example, due to high wellbore pressure assisting the stuck condition), the operator can immediately switch to downward jarring to shear the pin and free the tool string, without a trip out of the hole. How to Order: Specify nominal size and RMF designation. Contact Rebco for assembly numbers and release load specifications for both directions. Back to the Tool page PDF download RMF Pulling Tool Assembly RMF Pulling Tool Assembly Click here RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco ’s Terms and Conditions of Sale.

XNH & XOH Instrument Hanger Assembly 'BHP' Instrument Hangers XNH & XOH Instrument Hanger Assembly XNH & XOH Instrument Hanger Assembly Rebco XNH Instrument Hanger Assembly is used to land and lock geophysical instruments in ROTXN Landing Nipples respectively, to allow recording of reservoir data. Rebco XOH Instrument Hanger Assembly is used to land and lock geophysical instruments in ROTX Landing Nipples respectively, to allow recording of reservoir data. Product Code: 33 REQUEST A QUOTE DOWNLOAD DATASHEET XNH & XOH Instrument Hanger Assembly XNH & XOH Instrument Hanger Assembly Click here Applications Deploying BHP recording instruments into ROTXN nipples (XNH) or ROTX nipples (XOH) Small-bore completions requiring instrument hanger capability from 1.900" nominal and upward Sour service environments requiring NACE-compliant construction Key Benefits Covers the widest nominal size range of any Rebco instrument hanger from 1.900" through 5½." The Protector Sleeve design eliminates the Seal Stack and O-Ring Seal, simplifying assembly and reducing consumable usage. ROTX Running Tool and ROTGR Pulling Tool provide a complete, dedicated run-and-retrieve pair NACE MR-01-75 alloy construction standard across all sizes Lock mandrel parts are available separately for field repair. The Instrument Hanger Assembly consists of Lock Mandrel Assembly (DET 1), Protector Sleeve (DET 3) and a Hanger Sub (DET 2); offered with Amerada (3/4" - 16) Box connection and/or Sucker Rod (15/16" - 10) Box connection. NOTE: Lock Mandrel does not require Seal Stack or 'O' Ring Seal; instead, a Protector Sleeve is supplied to minimize the damage to the Packing Mandrel. A list of Assembly Sizes shown are not limited to the availability of other Sizes required, or Materials to suit well conditions. Please specify when ordering. RUNNING AND PULLING TOOLS REQUIRED: Select by Nominal Size - Seal Bore Size Running Tool: ROTX , Section III, Product Code 41 Pulling Tool: ROTGR , Section IV, Product Code 40 TECHNICAL DATA NOM SIZE SEAL BORE SIZE ASSEMBLY NUMBER LOCK MANDREL SUB-ASS’Y PROTECTOR SLEEVE HANGER SUB BOX THREAD BOX THREAD w/3/4” - 16 w/15/16” - 10 3/4” - 16 15/16” - 10 Type ‘XNH’ Instrument Hanger 1.900” 1.500” 3318100615030 3318100615031 10181015030 33001 33201815030 33201815031 2 1/16” 1.625” 3318100616230 3318100616231 10181016230 33002 33201816230 33201816231 2 3/8” 1.875” 3318100618730 3318100618731 10181018730 33005 33201818730 33201818731 2 7/8” 2.313” 3318100623130 3318100623131 10181023130 33009 33201823130 33201823131 3 1/2” 2.750” 3318100627530 3318100627531 10181027530 330012 33201827530 33201827531 2.813” 3318100628130 3318100628131 10181028130 330012 33201828130 33201828131 2.875” 3318100628730 3318100628731 10181028730 330012 33201828730 33201828731 4” 4 1/2" 3.313” 3318100633130 3318100633131 18181033130 330013 33201833130 33201833131 3.813” 3318100638130 3318100638131 18181038130 330015 33201838130 33201838131 5” 5 1/2" 4.313” 3318100643130 3318100643131 18181043130 330017 33201843130 33201843131 4.562” 3318100645630 3318100645631 18181045630 330018 33201845630 33201845631 Type ‘XOH’ Instrument Hanger 1.900” 1.500” 3318200615030 3318200615031 10182015030 33001 33201815030 33201815031 2 1/16” 1.625” 3318200616230 3318200616231 10182016230 33002 33201816230 33201816231 2 3/8” 1.875” 3318200618730 3318200618731 10182018730 33005 33201818730 33201818731 2 7/8” 2.313” 3318200623130 3318200623131 10182023130 33009 33201823130 33201823131 3 1/2” 2.750” 3318200627530 3318200627531 10182027530 330012 33201827530 33201827531 2.813” 3318200628130 3318200628131 10182028130 330012 33201828130 33201828131 2.875” 3318200628730 3318200628731 10182028730 330012 33201828730 33201828731 4” 4 1/2" 3.313” 3318200633130 3318200633131 18182033130 330013 33201833130 33201833131 3.813” 3318200638130 3318200638131 18182038130 330015 33201838130 33201838131 5” 5 1/2" 4.313” 3318200643130 3318200643131 18182043130 330017 33201843130 33201843131 4.562” 3318200645630 3318200645631 18182045630 330018 33201845630 33201845631 RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

ROTX Equalizing Valve Sub-Assembly Equalizing Sub-Assemblies ROTX Equalizing Valve Sub-Assembly ROTX Equalizing Valve Sub-Assembly Rebco ROTX Equalizing Sub-Assembly is to be used with ROTX & ROTXN Lock Mandrels. These Sub-Assemblies are designed to allow pressure differentials to be equalized across the Lock Mandrels and Flow controls before attempting to retrieve them from respective Landing Nipples. Product Code: 20 REQUEST A QUOTE DOWNLOAD DATASHEET ROTX Equalizing Valve Sub-Assembly ROTX Equalizing Valve Sub-Assembly Click here Applications Equalizing pressure across ROTX and ROTXN Lock Mandrels in their respective Landing Nipples, across nipple seal bores of 1.500" through 4.562", before retrieval operations Small-bore completions beginning at 1.500" seal bore, matching the ROTX lock mandrel's coverage down to 1.250" nominal H2S environments requiring Norm Alloy construction per NACE MR-01-75 Applications where the End Cap or without-Cap (suffix 1) configuration is required for specific assembly needs Key Benefits One-to-one pairing of assembly numbers between the ROTX Equalizing Sub and the corresponding ROTX or ROTXN Lock Mandrel eliminates selection ambiguity and ensures field accuracy. Covers the full ROTX and ROTXN lock mandrel size range, from 1.500" through 4.562" nipple seal bore. Available with or without an end cap for assembly flexibility. Norm Alloy construction for H2S service; a variety of materials available. Norm Alloy (NACE MR-01-75,1980 Rev.) Note: ROTX Equalizing Sub-Assemblies are available in variety of Materials. Lock Mandrels - see PRODUCT CODE 10, 17 and 18 TECHNICAL DATA NOMINAL SIZE 1.500” 1.625” 1.875” 2.313” 2.750” ASSEMBLY NUMBER 20182015030 20182016230 20182018730 20182023130 20182027530 ENGINEERING DATA MAXIMUM OD – No-Go 1.495” 1.620” 1.870” 2.307” 2.745” BOX THREAD CONNECTION 1 1/8” - 16 1 1/8” - 16 1 3/8” - 14 1 3/4” - 12 2 1/4” - 12 SLB PIN THREAD CONNECTION 1 1/8” - 16 1 1/8” - 16 1 3/8” - 14 1 3/4” - 12 2 1/4” - 12 SLB LENGTH 8.12” 8.12” 8.12” 8.25” 8.02” MATERIAL* Norm Alloy* Norm Alloy* Norm Alloy* Norm Alloy* Norm Alloy* To be used with Lock Mandrel ROTX 10182015030 10182016230 10182018730 10182023130 10182027530 ROTXN 10181015030 10181016230 10181018730 101810230 10181027530 Sub-Assembly without Cap 20182015031 20182016231 20182018731 20182023131 20182027531 NOMINAL SIZE 2.813” 2.875” 3.313” 3.813” 4.562” ASSEMBLY NUMBER 20182028130 20182028730 20182033130 20182038130 20182045630 ENGINEERING DATA MAXIMUM OD – No-Go 2.808” 2.870” 3.307” 3.807” 4.556” BOX THREAD CONNECTION 2 1/4” - 12 SLB 2 1/4” - 12 SLB 2 3/4” - 12 SLB 3 1/16” - 12 SLB 4” - 12 SLB PIN THREAD CONNECTION 2 1/4” - 12 SLB 2 1/4” - 12 SLB 2 3/4” - 12 SLB 3 1/16” - 12 SLB 4” - 12 SLB LENGTH 8.02” 8.02” 8.02” 8.63” 10.42” MATERIAL* Norm Alloy* Norm Alloy* Norm Alloy* Norm Alloy* Norm Alloy* To be used with Lock Mandrel ROTX 10182028130 10182028730 1818203310 18182038130 18182045630 ROTXN 10181028130 10181028730 1818103310 18181038130 18181045630 Sub-Assembly without Cap 20182028131 20182028731 20182033131 20182038131 20182045631 Norm Alloy (NACE MR-01-75, 1980 Rev.) RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.

Glossary ROTE & ROTK (Bottom No-Go) Lock Mandrel Sub-Assembly ROTE & ROTK (Bottom No-Go) Lock Mandrel Sub-Assembly The Rebco ROTE and ROTK are Bottom No-Go Lock Mandrel Sub-Assemblies, the large-bore counterparts to the ROTF and ROTM , designed for use in BR Landing Nipples with seal bores ranging from 2.750" to 3.812". As with the ROTF and ROTM pairing, the ROTK is essentially the ROTE sub-assembly without the Packing Unit and Packing Mandrel; the ROTE includes the full Packing Unit for pack-off applications. Both feature internal Fishing Necks providing large flow areas, and Collet-type locking fingers paired with Bottom No-Go shoulders to resist movement in both directions once set. Available in nominal 3 1/2" tubing (seal bores of 2.750" and 2.812") and nominal 4 1/2" tubing (seal bores of 3.688", 3.750", and 3.812"), the ROTE and ROTK share the same ROTGS Running/Pulling Tool and ROTM -specific prong used for the ROTF and ROTM family, keeping tool requirements consistent across the larger bore lock range. All sizes are constructed from Norm Alloy, and a variety of alternative materials are available for specific downhole conditions. How to Order: Product Code 10. Specify lock type ( ROTE for pack-off, ROTK for no pack-off), nominal tubing size (3 1/2" or 4 1/2"), seal bore size, thread type (Box for ROTE , Pin for ROTK ), and material. Back to the Tool page PDF download ROTE & ROTK (Bottom No-Go) Lock Mandrel Sub-Assembly ROTE & ROTK (Bottom No-Go) Lock Mandrel Sub-Assembly Click here RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco ’s Terms and Conditions of Sale.

BD Rope Sockets Tool String BD Rope Sockets BD Rope Sockets Rebco BD Rope Sockets are recommended to be used with up to.125" diameter Single Strand Wire. BD Rope Sockets are made up of BO Rope Socket Assembly and RQLD Bottom Sub-Assembly. Product Code: 100 REQUEST A QUOTE DOWNLOAD DATASHEET BD Rope Sockets BD Rope Sockets Click here Applications Designed for high-tension wireline connections that require rapid assembly and disassembly. Ideal for multi-run operations where efficiency is essential. Key Benefits Provides a self-tightening grip under load with the convenience of quick-lock operation. Double-shoulder RQLD connection prevents accidental partial engagement. Constructed from robust alloy steel for durability. Alloy Material is used to manufacture Rebco ROPE SOCKETS. Materials suitable for specific well conditions are available. Specify Wire Size Required Note: RQLD stands for ( Rebco Quick Lock Disconnect) TECHNICAL DATA NOMINAL SIZE 1 1/2” 1 3/4” 1 7/8” 2 1/8” 2 1/2” ASSEMBLY NUMBER 10001031500 10001031750 10001031870 10001032120 10001032500 ENGINEERING DATA: FISHING NECK OD 1.375” 1.75” 1.750” 1.750” 2.313” BOX CONNECTION 'RQLD' 'RQLD' 'RQLD'" 'RQLD' 'RQLD' MAXIMUM OD 1.38” 1.75” 1.88” 2.12” 2.50” LENGTH 12.16” 12.16” 12.16” 12.16” 12.16” MATERIAL Alloy Alloy Alloy Alloy Alloy RELATED TOOLS Disclaimer: Information is provided for reference only. Rebco Oil Tools, Inc. makes no express or implied warranty as to the accuracy or completeness of this information. Equipment selection, configuration, and use must be performed by qualified personnel and are subject to approved procedures, well conditions, mechanical limitations, and Rebco’s Terms and Conditions of Sale.