Lock Mandrels
LOCK MANDRELS were designed to land and set into downhole pre-positioned Landing Nipples (see Section XIII) in the well. The Lock Mandrels can be Selective or No-Go type depending on flow control accessory type attached to it.
The following pages will list some of the most common types of LOCKS for Landing Nipples and Tubing, offered by Rebco.
Rebco Type ‘ROTR’, ‘ROTRN’, ‘ROTX’, ‘ROTXN’, Lock Mandrels are offered with following features.
TUBING MANDRELS are designed to lock and pack off Wireline retrievable flow controls in wells that do not have Landing Nipples.
Type 'ROTR' Lock Mandrel Assembly
Rebco Type 'ROTR' Lock Mandrel is a Selective Set Lock to be set in Type 'ROTR' Landing Nipple of the same Size.
Product Code: 10
Lock Mandrels with Safety Spring, and Interference Hold Down are available, see PRODUCT 17 and 18
Type 'ROTRN' Lock Mandrel Assembly
Rebco Type 'ROTRN' Lock Mandrel has chamfered Keys, and when a Bottom Sub is added, it becomes a No-Go Lock Mandrel. It is to be landed in a Type 'ROTRN' Landing Nipple of the same size.
Lock Mandrels are available in a variety of Materials, suitable to down-hole conditions.
Product Code: 10
Type 'ROTR' and Type 'ROTRN' Lock Mandrel Assembly with Interference Hold Down
Rebco Lock Mandrels with Interference Hold Down feature provide positive latching structure which minimizes the possibility of the lock mandrel accidently unlocking due to vibration at high flow rates. Lock Mandrels with Interference Hold Down safety feature are available in a variety of Materials, suitable to down-hole conditions.
Product Code: 17
Type 'ROTR' and Type 'ROTRN' Lock Mandrel Assembly with Safety Spring
Rebco Lock Mandrels with Safety Spring and Shear Pin(s) feature holds the Key Expander Sleeve locked under flowing conditions. Lock Mandrels (PRODUCT CODE 18) in addition to Safety Spring and Shear Pin(s), have Expander Sleeve (DET 2) and Key Retainer (DET 3) different than the ones used in Product Code 10 Lock Mandrels.
Product Code: 18
Type 'ROTRQ' Lock Mandrel Assembly with Safety Spring and Shear Pin(s)
Rebco Type 'ROTRQ' Lock Mandrels with Safety Spring and Shear Pin(s) are Top No-Go Lock Mandrels designed to land and lock Sub-Surface Safety Valves in Type 'ROTRQ' Landing Nipples.
Other Sizes (not listed) are available, please inquire.
Type 'ROTX' Lock Mandrel Assembly
Rebco Type 'ROTX' Lock Mandrel is a Selective Set Lock to be set in Type 'ROTX' Landing Nipple of the same Size.
Product Code: 10
Lock Mandrels with Safety Spring, and Interference Hold Down are available, see PRODUCT 17 and 18
Type 'ROTXN' Lock Mandrel Assembly
Rebco Type 'ROTXN' Lock Mandrel has chamfered keys, and when a Bottom Sub is added, it becomes a No-Go Lock Mandrel. It is to be landed in a Type 'ROTXN' Landing Nipple of the same size.
Product Code: 10
Lock Mandrels with Safety Spring, and Interference Hold Down are available, see PRODUCT 17 and 18
Type 'ROTX' and Type 'ROTXN' Lock Mandrel Assembly with Interference Hold Down
Rebco Lock Mandrels with Interference Hold Down feature provide positive latching structure which minimizes the possibility of the lock mandrel accidently unlocking due to vibration at high flow rates. Lock Mandrels with Interference Hold Down safety feature are available in a variety of Materials and Sizes, suitable to down-hole conditions.
Product Code: 17
Type 'ROTS-1' & 'ROTS-2' Lock Mandrel Sub-Assembly
Rebco Type 'ROTS-1' & 'ROTS-2' Lock Mandrel Sub-Assembly is a Selective Non Flowing Lock. Lock Mandrel Sub-Assembly has Dogs (DET 2) facing both ways, up facing Dogs prevent Lock moving upward, and down facing prevent the Lock moving downward.
Product Code: 10
Type 'ROTW-1' & 'ROTW-2' Lock Mandrel Sub-Assembly
Rebco Type 'ROTW-1' & 'ROTW-2' is a Top No-Go, Non Flowing Lock. Lock Mandrel Sub-Assembly has Locks (Dogs) which prevent upward movement and a No-Go shoulder that seats in the upper part of a seating product to prevent downward movement.
NOTE: Required Running and Pulling Tools with appropriate Probes are shown in ENGINEERING DATA for Type of Accessories attached to the Lock Mandrel Sub-Assembly.
Type 'ROTZ-1' & 'ROTZ-2' Lock Mandrel Sub-Assembly
Rebco Type 'ROTZ-1' & 'ROTZ-2' is a Bottom No-Go, Non Flowing Lock. Lock Mandrel Sub-Assembly has Locks (Dogs) facing up which prevent upward movement, but depends on accessory No-Go shoulder to prevent the Lock Mandrel from downward movement. The Lock Mandrel can be used in a Bottom No-Go type Nipple only.
Product Code: 10
Type 'ROTG' & 'ROTN' (Top No-Go) Lock Mandrel Sub-Assembly
Rebco Type 'ROTG' and 'ROTN' are Top No-Go, Lock Mandrel Sub-Assembly to be set into Type 'BF' and Type 'BJ' Landing nipples, and Type 'BL' Sliding Sleeve.
Type 'ROTG' Lock is basically a Type 'ROTN' Lock Sub-Assembly less the Packing Unit and Packing Mandrel.
Product Code: 10
Type 'ROTR' & 'ROTL' (Bottom No-Go) Lock Mandrel Sub-Assembly
Rebco Type 'ROTR' and 'ROTL' are Bottom No-Go, Lock Mandrel Sub-Assembly to be set into Type 'BR' Landing nipple.
Type 'ROTR' Lock is basically a Type 'ROTL' Lock Sub-Assembly less the Packing Unit and Packing Mandrel.
Product Code: 10
Type 'ROTF' & 'ROTM' (Top No-Go) Lock Mandrel Sub-Assembly
Rebco Type 'ROTF' and Type 'ROTM' are Top No-Go, Lock Mandrel Sub-Assembly to be set into Type 'BF' and Type 'BJ' Landing nipples, and Type 'BL' Sliding Sleeve.
Type 'ROTF' Lock is basically a Type 'ROTM' Lock Sub-Assembly less the Packing Unit and Packing Mandrel.
Type 'ROTE' & 'ROTK' (Bottom No-Go) Lock Mandrel Sub-Assembly
Rebco Type 'ROTE' and Type 'ROTK' are Bottom No-Go, Lock Mandrel Sub-Assembly to be set into Type 'BR' Landing nipple.
Type 'ROTK' Lock is basically a Type 'ROTE' Lock Sub-Assembly less the Packing Unit and Packing Mandrel.
Type 'ROTD' Collar Lock Mandrel Sub-Assembly
Rebco Type 'ROTD' Collar Lock Mandrel Sub-Assembly is designed to be set in API Tubing Collars. The Tubing is sealed off by adding the Type 'ROTD' Element Assembly, and variety of Sub- Assemblies to suit application; capable to hold pressure differentials in both directions.
Product Code: 10
Type 'ROTTS' Collar Lock Mandrel Sub-Assembly
Rebco Type 'ROTTS' Collar Lock Mandrel Sub-Assembly is designed to be set in API Tubing Collars. Type 'ROTTS' Collar Lock Mandrel is basically the same as Type 'ROTS-2' Lock Mandrel Sub- Assembly (Product 10); with modified Keys (DET 2) to be able to locate in the Tubing Collars.
Product Code: 10
Type 'ROTW' Tubing Slip Mandrel Sub-Assembly
Rebco Type 'ROTW' Slip Mandrel Sub-Assembly is to be set into the Tubing without Nipples. The Element Sub-Assembly is designed to pack off the tubing ID.
NOTE: Type 'ROTW' Mandrel, attached with various types of Equalizing Sub-Assemblies, is designed to hold pressure from below only.
Product Code: 10